Lost your 2014 Ford Taurus Key Fob or need to program a new one? You’re in the right place. Programming your key fob yourself can save you time and money compared to visiting a dealership. This guide will walk you through different procedures that might work for your 2014 Ford Taurus, allowing you to regain control and convenience quickly. Remember, these are general procedures, and your owner’s manual is always the best resource for vehicle-specific instructions. If you don’t have your manual, don’t worry, try these methods to see if they work for your Ford Taurus.
Understanding Your 2014 Ford Taurus Key Fob Programming
Before you start, it’s important to understand that these procedures are designed to reset all remotes for your vehicle. This means any existing, functioning key fobs will also need to be reprogrammed during this process. Make sure you have all the key fobs you intend to use with your 2014 Ford Taurus ready before you begin. Also, a crucial tip to keep in mind throughout these steps: avoid pressing the brake pedal at any point before or during the programming process.
Programming Procedures for Your 2014 Ford Taurus Key Fob
Let’s explore two common procedures for programming your 2014 Ford Taurus key fob. Try Procedure A first, and if it doesn’t work, move on to Procedure B.
Procedure A
This procedure involves using the driver’s side door and ignition to enter programming mode:
- Start with the Driver’s Door: Ensure all doors are closed. Then, open only the driver’s side door. Leave it open. Press the “Unlock” button located on the driver’s side door panel while the door is open. Insert your key into the ignition.
- Ignition Cycling: This is the core of entering programming mode. Turn the ignition key rapidly from the “OFF” position to the “RUN” position eight times within an eight-second period. The eighth turn should end in the “RUN” position. Listen carefully for the door locks to cycle (lock then unlock). This cycling indicates that your 2014 Ford Taurus has successfully entered programming mode. If the locks do not cycle, you’ll need to remove the key and repeat from step 1, ensuring you perform the ignition turns quickly and correctly. “OFF” is the position where you can remove your key, and “RUN” is the position just before starting the engine.
- Program the First Key Fob: Within 10 seconds of the door locks cycling, take your first keyless remote (the one you want to program) and press any button on it. Again, listen for the door locks to cycle. This confirms that the first key fob has been successfully programmed.
- Program Additional Key Fobs (If Applicable): If you have more than one key fob to program for your 2014 Ford Taurus, repeat step 3 for each additional remote. Make sure to do this within 10 seconds of the previous programming confirmation (door lock cycle).
- Exit Programming Mode: Once you have programmed all your key fobs, turn the ignition key to the “OFF” position. The door locks should cycle one last time, signaling that the programming mode has ended.
If Procedure A does not work initially, try repeating it with the driver’s door closed during the ignition cycling portion.
Procedure B
Procedure B is a slightly different method that some Ford vehicles respond to:
- Prepare the Vehicle: Fasten your seatbelt and ensure all doors, including the trunk or liftgate, are completely closed.
- Ignition Cycling (4 Times): Turn the ignition key from the “OFF” position to the “RUN” position four times in rapid succession, specifically within a 3-second timeframe.
- Ignition OFF and Chime: Turn the ignition to the “OFF” position after the cycles. Listen for a chime sound from your 2014 Ford Taurus. This chime confirms that the vehicle has entered key fob programming mode.
- Program Key Fobs: Within 10 seconds of hearing the chime, take your first keyless remote and press and hold any button on it. Listen for a chime again; a single chime confirms successful programming of that remote.
- Program Additional Remotes: If you have more key fobs, repeat step 4 for each one, again within 10 seconds of the previous chime.
- Exit Mode: Turn the ignition key to the “RUN” position to exit the programming mode.
Remember, speed is important in Procedure B. Perform each step relatively quickly. If you don’t hear the initial chime or the door locks don’t cycle in either procedure, it indicates that your 2014 Ford Taurus hasn’t entered programming mode. In this case, remove the key, open and close the driver’s door, and carefully start the procedure over from the beginning.
Troubleshooting Tips
- Rapid Succession: Ensure you are performing the ignition turns and button presses in rapid succession as described in each procedure.
- Starting Over: If you don’t get confirmation (door lock cycle or chime), don’t hesitate to start over. It might take a few tries to get the timing right.
- Battery Condition: Low battery in the key fob or vehicle can sometimes interfere with programming. Ensure both are in good condition.
- Professional Help: If you’ve tried both procedures multiple times and are still unable to program your 2014 Ford Taurus key fob, it might be time to consult a professional locksmith or your local Ford dealership. They have specialized equipment and expertise to handle more complex programming issues.
For 2014 Ford Taurus models equipped with push-button start ignition and smart proximity keys, the programming procedure is different.
Smart Proximity Key for Push Button Start Ford Vehicles
For programming instructions specific to smart proximity keys for your 2014 Ford Taurus with push-button start, please visit KEY PROGRAMMING.
By following these steps, you should be able to program your 2014 Ford Taurus key fob and regain full functionality. Always refer to your owner’s manual for the most accurate and vehicle-specific instructions.
