Have you recently purchased a new key fob for your 2014 Honda CRV, or perhaps the battery died in your existing remote? Don’t worry about expensive dealership programming fees! As your trusted auto repair experts at keyfobx.com, we’re here to guide you through a quick and easy DIY programming process right in your driveway. Programming your 2014 Honda CRV key fob is simpler than you might think, and you can do it yourself in just a few minutes. Forget the dealership hassle and follow these straightforward steps to get your keyless entry working again.
Step-by-Step Guide to Program Your 2014 Honda CRV Key Fob
Follow these nine simple steps to program your 2014 Honda CRV key fob and regain keyless entry convenience.
Step 1: Gather All Your Honda CRV Remotes
Before you begin, make sure you have all the key fobs you intend to use with your 2014 Honda CRV. Even if you are only programming one new remote, all remotes must be programmed during the same session. This is because the system will reset and only recognize the remotes programmed in the current session. Any previously programmed remotes that are not included in this session will no longer work with your vehicle.
Step 2: Get Inside Your 2014 Honda CRV
Enter your 2014 Honda CRV and ensure all doors are fully closed and unlocked. This is crucial for the programming sequence to work correctly. Make sure no doors are ajar and that the vehicle is in an unlocked state before proceeding to the next step.
Step 3: Turn the Ignition Key to the ON Position
Insert your key into the ignition and turn it to the “ON” position. This is the position right before you would start the engine. You should see the accessory lights illuminate on your dashboard, and the instrument panel will light up. Do not start the engine; simply turn the key to the position where the car’s electrical systems are active.
Step 4: Press the LOCK Button (Within 5 Seconds of ON Position)
Within five seconds of turning the key to the “ON” position, locate your key fob and press the “LOCK” button for approximately one second. Timing is important here, so ensure you press the button quickly after turning the key.
Step 5: Turn the Ignition Key to the OFF Position
Immediately after pressing the “LOCK” button, turn the ignition key back to the “OFF” position. This turns off the accessory lights and the dashboard illumination.
Step 6: Repeat Steps 4 & 5 Two More Times (For a Total of Three Cycles)
Repeat steps 4 and 5 two more times, for a total of three on/off cycles. Each cycle must be completed within 5 seconds of the previous step to maintain the correct timing for entering programming mode. This means you will be turning the key to “ON,” pressing “LOCK,” turning to “OFF,” and repeating this sequence two more times.
Step 7: Turn the Key to the ON Position Again and Press LOCK (Enter Programming Mode)
Turn the key back to the “ON” position for the fourth time. Then, press the “LOCK” button on your remote one more time. If you have successfully entered programming mode, you will hear the door locks make a distinct “clunk” noise, just as if they were locking. It’s important to note that your doors have not actually locked; this noise simply indicates that your 2014 Honda CRV has entered Remote Programming Mode. Do not turn the key off at this point.
Step 8: Program Additional Remotes (Within 10 Seconds)
If you have additional key fobs to program, now is the time. Within 10 seconds of entering programming mode (hearing the “clunk” noise), press the “LOCK” button on each additional remote for one second. After each successful remote programming, you will hear the door locks “clunk” again, confirming that the remote’s signal has been successfully stored in your Honda CRV’s system memory. Remember, a maximum of three remotes can be programmed to a single 2014 Honda CRV.
Step 9: Turn the Key to the OFF Position and Test
Finally, turn the ignition key to the “OFF” position and remove it from the ignition. Now, test each of your programmed remotes to ensure they are working correctly. Press the lock and unlock buttons to verify that they are properly controlling the door locks of your 2014 Honda CRV.
Congratulations! You have successfully programmed your 2014 Honda CRV key fob. Remember that your remote will not operate if the key is in the ignition. If you’ve lost a keyless entry remote in the past, reprogramming your remotes is a smart security measure to protect your vehicle from potential theft. For more helpful guides and key fob solutions, remember to visit keyfobx.com, your trusted source for automotive key and remote expertise.
