Lost your key fob or need to program a new one for your 2015 Ford Explorer? You’re in the right place. Programming your key fob yourself can save you time and money compared to dealership services. This guide provides step-by-step instructions to program your 2015 Ford Explorer key fob for models with a regular keyed ignition.
This guide focuses on programming the remote functions of your key fob. It’s important to understand that these procedures are designed to reset all remotes associated with your vehicle. Therefore, if you have existing key fobs that are working, you will need to reprogram them along with any new ones during this process.
Before you begin, ensure you have all the key fobs you intend to program for your vehicle. Also, it’s crucial not to press the brake pedal at any point during or before the programming procedure unless specifically instructed otherwise.
Programming Procedures for 2015 Ford Explorer Key Fobs (Regular Keyed Ignition)
There are two primary procedures you can try to program your key fob. If one doesn’t work, move on to the other. It’s recommended to have your owner’s manual handy as it contains the specific procedure for your vehicle. If you don’t have your manual, these procedures are designed to cover most 2015 Ford Explorers with regular keyed ignition.
Procedure A: Door Lock Cycle Method
This procedure involves using the door locks to signal the vehicle to enter programming mode.
-
Prepare the Vehicle: Ensure all doors are closed. Open only the driver’s side door and leave it open. Press the “Unlock” button on the driver’s side door panel while the door is open. Insert your key into the ignition.
-
Enter Programming Mode: Turn the ignition key from the “OFF” position to the “RUN” position eight times within 8 seconds. The eighth turn should end in the “RUN” position. Listen for the door locks to cycle (lock then unlock). This cycling indicates that the vehicle has entered programming mode. If the door locks do not cycle, you’ll need to start over from step 1, ensuring you perform the key turns quickly and correctly. “OFF” is the position where you can remove your key, and “RUN” is the position just before starting the engine.
-
Program the First Key Fob: Within 10 seconds of the door locks cycling, press any button on the first keyless remote you want to program. The door locks should cycle again to confirm that the remote has been programmed.
-
Program Additional Key Fobs (If Applicable): If you have more than one key fob to program, within 10 seconds of the last lock cycle, press any button on the next keyless remote. The door locks will cycle again to confirm programming. Repeat this step for all remaining key fobs you wish to program.
-
Exit Programming Mode: Turn the ignition key to the “OFF” position. The door locks will cycle one last time to indicate that the programming mode has been exited.
* Troubleshooting Procedure A: If this procedure doesn’t work initially, try repeating it with the driver’s side door closed throughout the entire process.
Procedure B: Ignition Cycle and Chime Method
This procedure uses a faster ignition cycle and relies on a chime to indicate programming mode.
-
Prepare the Vehicle: Fasten your seatbelt and ensure all doors are completely closed.
-
Enter Programming Mode: Turn the ignition key from the “OFF” position to the “RUN” position four times within 3 seconds.
-
Confirmation Chime: Turn the ignition key back to the “OFF” position. You should hear a chime sound from the vehicle. This chime confirms that the system has entered programming mode.
-
Program the First Key Fob: Within 10 seconds of hearing the chime, press and hold any button on the first keyless remote you want to program. You should hear a chime once to confirm successful programming of this remote.
-
Program Additional Key Fobs (If Applicable): Within 10 seconds of the last chime, press and hold any button on the second keyless remote. You’ll hear another chime to confirm programming. Repeat for all other remotes.
-
Exit Programming Mode: Turn the ignition key to the “RUN” position to exit the programming mode.
Important Notes for Both Procedures:
- Speed is Key: Perform all steps in relatively quick succession. If you don’t get the initial door lock cycle (Procedure A) or chime (Procedure B), it means the vehicle hasn’t entered programming mode. Remove the key, open and close the driver’s door, and start the procedure again from the beginning.
- No Brake Pedal: Remember to avoid pressing the brake pedal at any point during these procedures unless specifically instructed by your owner’s manual for a different procedure.
- All Remotes: These procedures reset all programmed remotes. Make sure you reprogram all your working remotes along with any new ones in a single programming session.
Ford Key Fobs for 2015 Explorer Regular Keyed Ignition Systems
What About Push-Button Start?
The procedures above are specifically for 2015 Ford Explorers with a regular keyed ignition system. If your 2015 Ford Explorer has a push-button start ignition, the key fob programming procedure is different and involves smart proximity keys.
For programming instructions for 2015 Ford Explorer models equipped with a push-button start and smart proximity keys, please visit our dedicated guide on KEY PROGRAMMING.
Smart Proximity Key Fob for 2015 Ford Explorer Push-Button Start
Conclusion
Programming your 2015 Ford Explorer key fob for regular keyed ignition can be a straightforward process using either Procedure A or Procedure B. By following these steps carefully, you can quickly regain remote access to your vehicle. Remember to consult your owner’s manual for the most accurate procedure for your specific vehicle model.
If you continue to experience issues or need further assistance with key fob programming or replacement, keyfobx.com offers a wide range of services and resources to help you with your car key and remote needs.
