Is your C6 Corvette Key Fob acting up, or did you get a new one that needs programming? You’ve come to the right place. Programming your C6 Corvette key fob can seem daunting, but it’s actually a straightforward process you can tackle yourself. This guide will walk you through the steps to reprogram your key fobs, ensuring you’re back on the road quickly and without a trip to the dealership.
Understanding C6 Corvette Key Fob Programming
There are two main procedures for programming your C6 Corvette key fobs. The first procedure allows you to add new fobs while retaining the function of your existing ones. However, if you’re looking to ensure all your fobs are correctly synchronized and avoid potential memory function conflicts, the second procedure – reprogramming all fobs – is recommended. This method erases all previously programmed fobs and requires you to reprogram all fobs you intend to use with your Corvette. We will focus on this comprehensive reprogramming method to guarantee a clean slate and optimal performance for your c6 corvette key fob.
Step-by-Step Guide: Reprogramming Your C6 Corvette Key Fob (Long Procedure)
This procedure will erase all existing key fobs from your vehicle’s memory, so ensure you have all the fobs you wish to use ready to be programmed.
-
Preparation is Key: Begin by rolling down the driver’s side window and turning off your Corvette completely. Open both the trunk and the glove box. Crucially, make absolutely sure that NO key fobs are within range of the vehicle during this initial stage.
-
Initiate Programming Mode: Locate the keyhole inside the trunk. Insert your key into the trunk keyhole and turn it five times in rapid succession – make sure to complete these five turns in less than 5 seconds.
-
DIC Confirmation: After correctly performing step 2, your Driver Information Center (DIC) will beep and display the message “Off/Acc to learn”. If you decide to cancel the programming at this point, simply press the top half of the Start button to return the car to its normal state. Otherwise, proceed to step 4 to erase previous fobs and begin reprogramming.
-
Start 10-Minute Countdown (Round 1): Press the bottom half of the Start button. The DIC will now display a message indicating a 10-minute wait period and begin counting down. You can close the trunk and car door while you wait for this first countdown to complete.
-
Repeat Countdown (Round 2 & 3): Once the first 10-minute countdown finishes, the DIC will again show “Off/Acc to learn”. Press the bottom half of the Start button once more. Another 10-minute countdown will begin. Repeat this process a third time after the second countdown completes.
-
Ready for Fob Programming: After the third 10-minute period concludes, the DIC will display “Ready for Fob #1”. Now you can begin programming your fobs.
-
Program Fob #1: Take your first c6 corvette key fob and insert it into the glove box slot. Ensure the fob is placed with the buttons facing towards the passenger side and the keyring end pointing outwards.
-
DIC Confirmation and Subsequent Fobs: After a few seconds (approximately 3-4), the DIC will beep and display “Ready for Fob #2”. You can now insert your second fob into the glove box slot. Repeat this process for any additional fobs you need to program, up to a maximum of four fobs.
-
End Programming Session: Once you have programmed all your desired fobs, press the bottom half of the Start button to finalize the programming session.
Testing Your Programmed Key Fobs
After completing the programming procedure, it’s crucial to test each of your c6 corvette key fobs to ensure they are working correctly.
-
Button Functionality Test: Test all the buttons on each fob – lock, unlock, trunk release, and panic button – to confirm they are responding as expected.
-
Remote Start Test: Move away from the car with all fobs. Then, test each fob individually to start the car remotely. This confirms that each fob is properly paired with your C6 Corvette.
Important Notes:
- Canadian Spec Corvettes: While Canadian specification C6 Corvettes can use the shorter fob programming procedure, the longer procedure detailed here may require dealership programming.
- European Spec Corvettes: European specification C6 Corvettes generally require all key fob programming to be performed by an authorized dealer.
- Battery Maintenance: The long programming procedure can put a strain on your car battery. It’s advisable to connect a battery tender to your Corvette during the programming process to prevent battery discharge issues.
- Cell Phone Interference: It has been reported that having a cell phone on your person during the long programming method might cause interference, potentially disrupting the process at step #9. It’s recommended to keep your cell phone away from you and the vehicle during programming.
By following these steps carefully, you should be able to successfully program your c6 corvette key fob and regain full control over your vehicle’s keyless entry system. Enjoy the convenience of your newly programmed fobs!
