Lost your Pontiac G6 Key Fob or need to program a new one? Don’t want to spend a fortune at the dealership? The good news is, programming your Pontiac G6 key fob can be done right at home with a few simple steps. This guide will walk you through the process, allowing you to save time and money.
This DIY method is based on verified instructions and user experiences, ensuring you can confidently program your key fob without any special tools. Let’s get started!
Step-by-Step Guide to Program Your Pontiac G6 Key Fob
Before you begin, make sure you have all the key fobs you intend to use for your Pontiac G6. This programming process will erase all previously programmed key fobs, so you’ll need to reprogram them all at once. You can program up to four key fobs for your vehicle.
Here’s how to program your Pontiac G6 key fob:
-
Get Comfortable in the Driver’s Seat (or Passenger Seat): Sit in the driver’s seat. Some users find it easier to perform these steps from the front passenger seat, so choose whichever is most comfortable for you.
-
Remove the Ignition Key: Take the ignition key out of the ignition lock cylinder.
-
Close All Doors: Ensure all doors of your Pontiac G6 are completely closed.
-
Locate and Remove the MALL PGM Fuse: Find the fuse panel in your Pontiac G6. Refer to your owner’s manual if you’re unsure of its location. Identify and remove the “MALL PGM” fuse from the fuse panel. This fuse is related to the মাল্টিপ্লেক্সড অ্যাক্সেস কন্ট্রোল লিনক প্রোগ্রামিং and needs to be removed to initiate the programming sequence.
-
Turn Ignition to ACC: Insert your key into the ignition and turn it to the “ACC” (Accessory) position.
-
Cycle Ignition ACC and OFF: Turn the ignition from the “ACC” position to “OFF” and then back to “ACC” within one second. Do this quickly.
-
Open and Close Any Door: Open and then close any door on your Pontiac G6. This action signals the system to enter programming mode.
-
Listen for the Chime: You should hear a chime sound. This chime indicates that the remote control door lock receiver has successfully entered the programming/diagnostic mode. If you don’t hear a chime, repeat steps 1 through 7 again.
-
Program the Transmitter: Take the first key fob you want to program. Press and hold both the “LOCK” and “UNLOCK” buttons on the transmitter simultaneously for approximately 14 seconds.
-
Confirmation Chimes (Synchronization and Programming):
- After about 7 seconds of holding the buttons, you might hear a chime. This chime confirms successful synchronization.
- Continue holding the buttons for the full 14 seconds. After approximately 14 seconds, you should hear another chime. This second chime confirms successful programming of the key fob.
-
Program Additional Transmitters (If Any): If you have more key fobs to program, repeat step 9 for each additional transmitter. Remember, you must program all key fobs you want to use during this session.
-
Remove Ignition Key: Take the key out of the ignition lock cylinder.
-
Reinstall the MALL PGM Fuse: Go back to the fuse panel and reinstall the “MALL PGM” fuse that you removed in step 4.
-
Test Your Key Fobs: Test all the key fobs you just programmed to ensure they are working correctly. Check the lock, unlock, and any other functions your key fob may have, like remote start (if applicable to your Pontiac G6 model).
Important Notes and Tips
- Timing is Key: The timing in steps 6, 7, 9, and 10 is important. Try to follow the timeframes as closely as possible.
- All Fobs Must Be Programmed Together: As mentioned earlier, this process erases previous programming. Make sure you have all your key fobs ready to program during this session.
- Fuse Location: If you have trouble finding the MALL PGM fuse, consult your Pontiac G6 owner’s manual for a fuse box diagram.
- Troubleshooting: If you don’t hear the initial chime in step 8, double-check that you’ve followed each step correctly. Start from the beginning and try again.
- Aftermarket Key Fobs: These instructions should work for both original equipment manufacturer (OEM) key fobs and compatible aftermarket key fobs designed for the Pontiac G6.
By following these steps, you can program your Pontiac G6 key fob yourself and regain full remote access to your vehicle without the expensive trip to a locksmith or dealership. Enjoy the convenience of your newly programmed key fob!
